LDO Probe Parts & Full Probe Kits (Stainless Steel Z1 rails)

Note: Batch 1 PCB is larger V2 (5-24V) - Please ensure you print the correct parts. [OBP666]

Note: Kits does not include printed parts.

Note: As usual, only transport oil is apply to rail/carriage. Please clean and apply grease beforehand. Please use this printed parts to load rail from Tap Github. As this tight pre-load, please load carefully.

Note: Batch 2 will be higher priced OBP971N51 due to limited OBP666

Note: Current LDO kits are not R8 compatible. 

Note: Currently PCB are not sold separately due to supply issues (once LDO can supply them individually it will be restocked, if you after PCB only please check our our listing : https://store.dremc.com.au/products/voron-tap-tap-tap-kit 

INTRODUCTION: WELCOME TO TAP
WHAT IS TAP?
Tap is a nozzle-based z-probe for the V2 and Trident printer designs. The entire toolhead moves to trigger an optical switch. Tap offers many advantages over other z-probes;

EXTREME PRECISION
A well constructed Tap, when in service on a well-constructed printer, will be able to measure your Z position reliably with a precision of 0.4 μm (0.0004 mm). This precision will help you better use and maintain your printer.

ANY BUILD SURFACE, CHANGE AT WILL
Tap can measure any securely mounted build surface. Print on Glass, Garolite, Alumina, Moon dust...it no longer matters. Textured plates are ideal for Tap, but adhesive PEI sheets may also be used. Tap is unaffected by beds with magnetic fluctuations (note: magnets may affect the build surface Tap is sensing, such as pulling the plate tighter over the magnet). Once Tap is setup, you should not need to re calibrate after changing nozzles or build plates.

VORON DURABILITY, HIGH TEMPERATURE OPERATIONS
Tap uses light to detect movement and will never wear out. The sensor in Tap is rated to operate at 70C to 100C and will not degrade over time the way a contact switch or inductive probe can.

Hundreds of PIF quality kits were printed using Tap. Some test printers had over 1,000,000 probe cycles to test durability.

NO COMPLICATED MACROS
For consistent probing temperatures, Tap uses a single ‘activate_gcode’ macro in the [probe] config. Tap is always ready to probe and requires no docking or undocking moves.

Z ENDSTOP ELIMINATION
There is no need for a separate Z endstop. Once the offset is configured, it will hold without appreciable drift. It is normal to need slightly different offsets when switching between filament types.

CRASH PROTECTION
With Tap installed, the nozzle and bed are protected from minor crashes (such as accidentally setting your Z to 1 mm below the build surface

More Information: https://github.com/VoronDesign/Voron-Tap

TAP Probe Release Live stream: https://youtu.be/JLUDLJQXZeU

Bom: Custom Rails Only SS (Stainless Steel)

Bom: Custom Rails Only (Carbon Steel)

Bom: Full Kit: 

• Tap photosensor V2.4.1 
• Linear Rail stainless steel SLR9H-1R-50Z1-E5
• Hardware Kit
• 1 x M3 hex nut
• 6 × M3 washers
• 2 × M3x20 SHCS
• 2 × M3x16 SHCS
• 1 × M3x12 SHCS
• 3 × M3x8 SHCS
• 2 × M3x10 BHCS
• 1 × M3x6 SHCS
• 2 × M3x6 FHCS black oxide fully magnetic screws
• 10 × M3x6 BHCS
• 11 × Heatset inserts
• 2 × 6x3mm N35 Magnets